5/16/2023 0 Comments Softraid secure bootOr at the very least, if there is a hardware issue / incompatibility, it likely only explains the UEFI booting issue (though why it can UEFI boot off the install USB stick is a good question in that case).Ĭan anyone provide me a direction to look into next? As it is I'm kind of stuck-been having a spate of HDD failures lately and I'd really like to get the softraid boot working properly. I don't think there's a problem with the hardware as I've been running OpenBSD on this machine for some time (albeit 6.5, and doing a single-disk MBR boot). Some googling led me to believe the UEFI boot loader might be missing from the "i" partition, but I booted from the USB key and checked the "i" partition on both members of the mirror (sd0i/sd1i) and the UEFI files are there. I can UEFI boot from the install image on the USB key, but I can't UEFI boot at all from the hard disks. I'm not sure why this is happening, but I thought "Well, maybe it's time to try UEFI boot and see what that does." This is new so I go check-/etc/nf indeed doesn't exist, but /etc/ed does. I know at some point there were size limitations and issues with /boot or /bsd being too far from the beginning of the disk, but I've never run into them and I don't know if they're still an issue.Īnyway, the softraid boot works fine, but on every single boot it complains that it can't read /etc/nf or /etc/ed. I've been doing that for years and never run into a problem booting. So I created a single large "a" partition and installed to that. Note that I never use the default disk layout, I really dislike having multiple partitions and the annoyance that comes with never having the disk space you need in the partition you need. Then I installed on to sd3 (sd2 ends up being the boot USB drive) and reboot. I dropped to the shell, setup the softraid the same way I always do (initialize each disk with fdisk -iy, setup the disklabel, use bioctl to mirror the drives). I am trying to set these drives up as a mirror and get the system to boot off of it.įirst I tried just doing the standard MBR boot like I always do. New machine is running an i2500k on ASRock Z77 Pro4, 16GB RAM, and 2x2TB hard drives (sd0 and sd1). I'm trying to do a fresh install of 6.7 on the new machine and running into issues. I'm "moving" my firewall install from one physical machine to another (this is basically intended to be a forklift upgrade). Normally I've been able to solve pretty much all of my problems just by searching the internet, but this one has me stumped. While the requirement to upgrade a Windows 10 device to Windows 11 is only that the PC be Secure Boot capable by having UEFI/BIOS enabled, you may also consider enabling or turning Secure Boot on for better security.First time poster here, longtime OpenBSD user (since about 2.1 or so). Here are a few links to information from some PC manufacturers to help get you started: If you are unsure how to make any necessary changes to enable the UEFI/BIOS, we recommend that you check your PC manufacturer’s support information on their website. If so, you will need to choose for UEFI to be the first or only option. In some cases, there are options to enable both UEFI and Legacy/CSM. To change these settings, you will need to switch the PC boot mode from one enabled as “Legacy” BIOS (also known as “CSM” Mode) to UEFI/BIOS (Unified Extensible Firmware Interface). To access these settings, you can consult your PC manufacturer’s documentation or follow these instructions: Run Settings > Update & Security > Recovery and select Restart now under Advanced startup. From the next screen, select Troubleshoot > Advanced options > UEFI Firmware Settings > Restart to make changes. Firmware, often called BIOS (Basic Input/Output System), is the software that starts up before Windows when you first turn on your PC. Most modern PCs are capable of Secure Boot, but in some instances, there may be settings that cause the PC to appear to not be capable of Secure Boot. These settings can be changed in the PC firmware. Secure Boot is an important security feature designed to prevent malicious software from loading when your PC starts up (boots). This article is intended for users who are not able to upgrade to Windows 11 because their PC is not currently Secure Boot capable. If you are unfamiliar with this level of technical detail, we recommend that you consult your PC manufacturer’s support information for more instructions specific to your device.
0 Comments
Leave a Reply. |